Blog

A preventive maintenance calendar for residential and commercial properties

Zrico team ·
In short

A preventive maintenance calendar lists every recurring task for every major building system, with a frequency, a season and an owner, and turns each into a work order on schedule. Build it from an asset list, group tasks by month so vendors visit once, and track the share of tasks done on time.

Most emergency calls at night are preventive tasks that didn't happen. A clogged dryer vent, a gutter that overflowed into a wall, a water heater that hadn't been looked at in nine years. A preventive calendar won't remove emergencies, but it moves a large share of maintenance spend from the worst time to the time you choose. This guide shows how to build one, with a sample calendar for residential and commercial properties.

Required inspection and testing schedules, for fire systems, elevators, backflow devices, boilers and similar equipment, are set by local codes, your insurer and manufacturers, and they vary by place and equipment. Use the frequencies below as a starting point, and confirm the required ones with your local authority, your insurer and licensed vendors.

Step 1: Build the asset list

You can't schedule what you haven't listed. For each property, record:

  • Roofs: type, age, last inspection and any warranty
  • HVAC: each unit or system, with make, model, serial number, install year and filter size
  • Water heaters and boilers: type, capacity, install year
  • Fire and life safety: alarm panel, sprinklers, extinguishers, emergency lights, smoke and carbon monoxide alarms
  • Plumbing: main shutoff locations, backflow devices, sump pumps, sewer laterals on older buildings
  • Elevators, generators and gates, where present
  • Appliances in units, with install year
  • Site: parking, sidewalks, irrigation, drainage, trees

Install year matters most. It drives both the schedule and the replacement forecast, so an owner hears about a 14-year-old boiler before it fails rather than after.

Step 2: Assign a frequency and a season

Every task gets a frequency, such as monthly, quarterly, twice a year or yearly, and, where it matters, a season. Gutters belong in late fall after leaves drop. Cooling service belongs in spring before the first hot week. Irrigation start-up waits for the last frost. Tasks that depend on the season should be on fixed months, not rolling intervals, or they drift into the wrong time of year.

Step 3: Group tasks so vendors visit once

If the HVAC vendor visits 40 Grove St in April for cooling service and again in May for a filter change, you are paying for two trips. Group tasks by vendor and property into the same month where you can. For in-house techs, group by property and building so each visit covers several tasks.

A sample residential calendar

These are common frequencies for multifamily and single-family rentals. Adjust them to your climate, buildings and requirements.

Monthly

  • Walk the common areas and exterior: lighting, trip hazards, trash areas, signs of leaks
  • Check fire extinguishers visually: gauge in the green, pin and seal in place, tag current
  • Test emergency lighting and exit signs in common areas
  • Check sump pumps and common-area drains
  • Change HVAC filters in common areas, and in units where the lease makes it your job

Quarterly

  • Change HVAC filters in units, if not monthly
  • Pest control service for common areas and on request in units
  • Inspect roofs from the ground and clear roof drains on flat roofs
  • Run the generator under load, where present, per the manufacturer

Spring

  • Cooling service on HVAC systems before the first hot weeks
  • Roof inspection, with photos, after winter
  • Irrigation start-up and leak check
  • Exterior walk for siding, paint, caulking and sealants
  • Clean gutters and downspouts where trees drop seeds and flowers

Fall

  • Heating service on furnaces and boilers before the first cold weeks
  • Gutters and downspouts cleaned after leaves drop
  • Irrigation winterized in freezing climates
  • Hose bibs and exposed pipes protected in freezing climates
  • Snow contracts confirmed, with salt and equipment stocked

Yearly

  • Smoke and carbon monoxide alarms tested in every unit, with batteries replaced where needed
  • Dryer vents cleaned, in every unit with a dryer
  • Water heaters inspected and flushed where the manufacturer recommends it
  • Fire extinguishers serviced by a licensed vendor
  • Fire alarm and sprinkler systems inspected and tested on the schedule your code and insurer require
  • Backflow devices tested where required
  • Unit inspections, interior, with photos
  • Trees inspected for dead limbs near buildings and walkways
  • Sewer lines on older buildings inspected by camera, and cleared where needed

A sample commercial calendar

Commercial buildings add systems and tenants' expectations, and often lease obligations about who maintains what. Read each lease for what the landlord maintains before you build the calendar.

Monthly

  • Walk the building and site: lighting, parking, sidewalks, signs, common restrooms
  • Test emergency lighting and exit signs, and keep the test log
  • Run generators under load per the manufacturer
  • Check rooftop units for alarms, noise and visible damage
  • Sweep the parking lot, or confirm the sweeping contract ran

Quarterly

  • Service rooftop HVAC units: filters, belts, coils and drains
  • Inspect roofs and clear drains, scuppers and gutters
  • Inspect and pump grease traps on the schedule the use requires
  • Review tenant-reported issues for repeats by system

Twice a year

  • Full roof inspection in spring and fall, with photos and a written report
  • Parking lot inspection for potholes, cracks and drainage, with repairs scheduled before winter
  • Exterior lighting survey after dark

Yearly

  • Fire alarm, sprinkler and suppression system inspections on the required schedule
  • Emergency lighting full-duration test where required
  • Elevator inspections and maintenance on the required schedule
  • Backflow testing where required
  • Building envelope review: sealants, windows, doors and loading docks
  • Parking lot sealcoat and line painting on a cycle the surface needs, often every few years

Step 4: Turn the calendar into work orders

A calendar on a spreadsheet gets forgotten. Each task should create a work order automatically on its date, assigned to a tech or vendor, with the checklist for that task attached. A completed work order is the proof the task was done, which matters to owners, insurers and buyers. Attach photos and readings, such as a water heater's install date plate or a generator's run hours.

Step 5: Budget it

Preventive work is a budget line, not a surprise. Price each task once, total it by property and month, and put it in next year's budget. An example for a 48-unit building: annual HVAC service contracts of $7,200.00, dryer vent cleaning of $1,920.00, gutter cleaning twice a year at $1,100.00, fire extinguisher and alarm service of $1,450.00 and pest control of $2,400.00 come to $14,070.00 for the year, spread across the months each task runs.

Who does the work: in-house or vendor?

Many preventive tasks suit in-house techs: filter changes, alarm tests, common-area walks and minor caulking. Tasks that need a license, special equipment or a signed inspection report usually go to vendors: fire systems, elevators, backflow testing and boiler inspections. Write the split into the calendar, so a task never sits unassigned because each side thought the other had it. For vendor tasks, confirm each vendor's insurance and license are current before the visit, and ask for the written report as part of the job.

What to track

  • Preventive tasks completed on time, as a share of tasks due. Below about 90% usually means the calendar is too ambitious or a vendor is slipping.
  • Planned vs reactive work orders. Over time, the share of planned work should rise.
  • Repeat failures on the same asset, which point to a repair or replacement decision.
  • Assets past their expected life, listed for the owner each year with a replacement estimate.

The setup checklist

  1. Asset list complete, with install years
  2. Required inspections confirmed with your local authority, insurer and vendors
  3. Each task has a frequency, a season where it matters and an owner
  4. Tasks grouped by vendor and property into shared months
  5. Recurring work orders created automatically, with checklists
  6. Preventive costs in next year's budget
  7. On-time completion reviewed monthly

How Zrico helps

Zrico runs recurring work orders for preventive care, keeps appliance records with a replacement forecast, and tracks inventory with reorder points, purchase orders and project budgets. Vendors get their jobs, payments and compliance papers in a vendor portal, and a workflow can remind vendors 30 days before their insurance or license expires. Giving a job to a vendor waits for a person by default; an admin can let Zrico book vendors under your spending limit in Settings. Read more at /product/maintenance.

See Zrico run your portfolio.

Bring a property. We will show you, on your own data, what Zrico would have handled last month.