Blog

Make-ready and turnover: a room-by-room checklist and a day-by-day timeline

Zrico team ·
In short

A fast turn starts when notice arrives, not at move-out: inspect early, order materials and book vendors before the unit is empty. Then work in a fixed order, trash out, repairs, paint, floors, appliances, clean, final inspection, so no trade undoes another, and track days from move-out to ready on every unit.

Every vacant day costs money that never comes back. On a unit that rents for $1,650.00, each day empty is about $54.25 of lost rent, so a turn that takes 14 days instead of 7 costs the owner about $380.00 before a single repair. Most of that time isn't spent working. It is spent waiting: for the scope, for the painter, for a part. This guide gives a timeline that removes the waiting, a room-by-room checklist, and the numbers worth tracking.

The timeline, from notice to ready

This example is for a standard turn on an apartment or single-family home in fair condition. Heavy turns take longer; the order stays the same.

  1. Notice received, about 30 days out: schedule a pre-move-out inspection with the resident, and confirm the move-out date and forwarding address in writing.
  2. Pre-move-out inspection, 2 to 3 weeks out: walk the unit, note the likely scope, photograph anything major and decide early on big items such as flooring or appliance replacement.
  3. Two weeks out: order long-lead materials, book the painter, cleaner and flooring vendor for specific days, and get owner approval for anything over the owner's limit.
  4. Move-out day: walk the unit with the move-out inspection form, take dated photos of every room, collect keys, record meter readings and start the deposit file.
  5. Day 1: confirm the final scope against the pre-move-out notes and trash out the unit.
  6. Days 1 to 3: repairs, including drywall, doors, hardware, plumbing, electrical and fixtures.
  7. Days 3 to 4: paint, after repairs are done and drywall patches are dry.
  8. Days 4 to 5: flooring, cleaned or replaced, after paint so floors aren't dripped on.
  9. Day 5: appliances checked and repaired, and the HVAC filter changed.
  10. Day 6: final cleaning, always the last trade in the unit.
  11. Day 6: rekey or change the lock code, and test every smoke and carbon monoxide alarm.
  12. Day 7: quality inspection by someone other than the person who did the work, with photos of every room.
  13. Day 7: unit marked ready, listing photos taken, and the unit opened for showings or a move-in.

A seven-day standard turn is a good target for many portfolios. Track the actual number and set your own target from it.

Why the order matters

Each trade can undo the one before it. Paint before repairs means patching and repainting. Floors before paint means drips on new carpet. Cleaning before the final punch list means a second clean. Schedule trades in the order above and hold vendors to their days, because one late painter pushes every trade after them.

Room-by-room checklist

Use the same checklist for every turn, in the same order as your move-in and move-out inspection forms, so findings line up room by room.

Entry and living areas

  • Front door: closes, latches and locks; weatherstrip in place; peephole clear
  • Walls and ceilings: holes patched, stains sealed, paint touched up or repainted
  • Floors: clean or replaced, no lifting seams, transitions secure
  • Windows: open, close and lock; screens intact; blinds work
  • Lights and switches: every fixture works, cover plates on, bulbs matched
  • Outlets: every outlet works, cover plates on

Kitchen

  • Range and oven: all burners and the oven heat, knobs present, clean inside and under
  • Refrigerator: cools to temperature, seals intact, ice maker and water line checked for leaks
  • Dishwasher: runs a full cycle, no leaks underneath, racks intact
  • Sink and faucet: no drips, sprayer works, disposal works, no leaks under the sink
  • Cabinets and drawers: open, close and stay aligned; shelves and hardware present
  • Counters: no burns or chips that need repair; caulk at backsplash intact
  • Range hood and fan: light and fan work; filter cleaned or replaced

Bathrooms

  • Toilet: flushes, no running, seat secure, no movement at the base
  • Tub and shower: drains freely, no leaks, caulk and grout clean and intact
  • Sink and vanity: no drips or leaks, drain stopper works
  • Exhaust fan: runs and vents
  • GFCI outlets: test and reset
  • Mirror, towel bars and accessories: secure and undamaged

Bedrooms

  • Doors: open, close and latch; locks work where fitted
  • Closets: doors on track, rods and shelves secure
  • Windows: open, close and lock; blinds work
  • Smoke alarm: tested, with a date noted

Laundry, utility and systems

  • Washer and dryer, if provided: run a cycle, no leaks
  • Dryer vent: clear and connected
  • Water heater: no leaks or corrosion, temperature set to your standard
  • HVAC: heats and cools, new filter installed, thermostat works
  • Smoke and carbon monoxide alarms: all tested and working
  • Main water shutoff: accessible and labeled

Exterior, for homes and ground-floor units

  • Patio or balcony: clean, railings secure
  • Yard: mowed, cleared and free of left-behind items
  • Exterior lights: working
  • Mailbox: key or code changed
  • Garage door and remote, if any: working, remote present

A sample turn budget

Here is an example budget for a standard turn on a two-bedroom unit. Your costs will differ by market and condition.

  • Trash out: $150.00
  • Repairs, drywall, doors and hardware: $420.00
  • Paint, touch-up and two accent walls: $650.00
  • Carpet cleaning: $180.00
  • Appliance repair: $160.00
  • Final cleaning: $275.00
  • Rekey: $85.00
  • Total: $1,920.00

Keep two things separate. First, turn costs that are the owner's normal expense, such as paint and cleaning at the end of a long tenancy. Second, damage charged to the former resident, which goes through the deposit process with its own documentation. Mixing them makes both the owner statement and the deposit statement harder to defend. Large items such as full carpet replacement or a new appliance may be capital improvements rather than repairs; follow the rule your accountant set.

Get owner approvals early

If any item is over the owner's spending limit, ask for approval at the pre-move-out inspection, not after move-out. A two-day wait for an owner to approve new carpet adds two vacant days. Send the photo, the bid and the cost of the vacant days the decision affects, so the owner can decide quickly.

The numbers to track per turn

  • Days from move-out to ready: the main number. Report the average and the slowest turns each month.
  • Days from ready to leased: a long gap here is a pricing or marketing problem, not a maintenance one.
  • Cost per turn: total cost, split into normal turn cost and damage charged back.
  • Callbacks: work orders opened by the new resident in the first 30 days. A high count means the quality inspection missed things.
  • Vendor on-time rate: the share of vendor visits done on the booked day.

A unit with a seven-day turn and a 21-day lease-up is not a fast turn. Track both numbers together, because the owner experiences them as one vacancy.

Turns in occupied buildings

In apartment buildings, a turn happens next to people who live there. Book loud work, such as demolition and flooring removal, inside the hours your building rules allow. Protect hallways and elevators on trash-out day, tell neighbors when a big job is coming, and park vendor vans where they won't block residents. A complaint from the unit next door costs more goodwill than a day of vacancy.

Common mistakes

  • Starting the scope on move-out day instead of at notice
  • Booking vendors one at a time, after the previous trade finishes
  • Skipping the quality inspection because the cleaner says it looks good
  • Not rekeying between residents
  • Listing photos taken before the clean, which show the unit at its worst

How Zrico helps

Zrico's make-ready tracks each unit turn from move-out to ready, with the costs on the unit. Room-by-room inspections with photos and video turn findings into work orders, vendors get their jobs in a vendor portal, and you can send collected bids to the owner portal for approval. A unit turns report shows how long turns take. Giving a job to a vendor waits for a person, even in Autopilot, unless an admin lets Zrico book vendors under your spending limit in Settings. Read more at /product/maintenance, and use the free layout at /templates/move-in-checklist for the inspection that comes next.

See Zrico run your portfolio.

Bring a property. We will show you, on your own data, what Zrico would have handled last month.